Fits the Model 1895, 336, 444, 375, 356 ER 336W ETC.
(all large frame models of Marlin lever action rifles.) (including the Marlin Guide Gun and MXLR series)
(other MARLINS marked under different names IE: Glenfield)
(All SKINNER 1895/336 sights fit the CAMP 45/9mm CARBINES)
The sight is designed to mount using the rear pre-drilled and tapped holes on the top of the receiver and is fully adjustable for windageand elevation. Adjustments are locked in place with set screws. This sight is precision manufactured to close tolerances and can be ordered in Blued Steel, Stainless Steel or Brass.
The removable .096" aperture (Installed) allows the marksman to use a fine aperture or a much larger ghost ring.
Other aperture sizes are available, please see our APERTURES page on the side bar. Mounting screws and wrenchs are included..
"Will my factory front sight work with this sight."
THE SKINNER "RELIABLE" SERIES
(Note: These photos were taken prior to our now standard and attractive engraved "SKINNER" brand on the sight. Current models are now marked "Skinner")
OUR XA SERIES 1895 / 336 SIGHT
XA = Extra aperture. This sight has a threaded hole in the forward "slope" of the sight that allows an extra aperture to be easily stored and available for those "changing light" conditions.
The XA comes standard with your choice of two aperture sizes.
(Please indicate which two sizes you would like in a Note to Merchant during the final stage of payment or send us an email immediately following check out indicating which two apertures you need)
(Sm, Med, Std, Lrg, Xlrg)
Price is $79 Blue, $81 Brass, $85 Stainless.
THE GUIDE GUN SET
In response to YOUR needs, Marlin brought out the incredible GUIDE GUN Series of rifles. These handy and quality rifles have been a tremendous success with shooters all over the world. We offer the Guide Gun Owner a special set of SKINNER SIGHTS that includes a "RAMPED FRONT" that is .070" wide. This special front sight reduces snagging in the scabbard and brush, is wide enough to see quickly yet narrow enough to not obscure the target. Our Guide Front Sight is nicely serrated on the back to reduce glare.
$79 in Blued Steel $85 in Stainless Steel
(note: Proper Front Sight Heights vary for numerous reasons. We ship a 1/4"X.500" sight with the Guide Gun Set. This sight can be "trimmed" to whatever height is needed. If you would rather have a different front sight, order the standard RELIABLE and add the front sight needed from our FRONT SIGHT page)
Note: For added features or for non Guide Gun models, please order the RELIABLE or XA and add the features you desire seperately. (Black Gold, Fiber Optic Front, etc)
The SKINNER EXPRESS SIGHT blends the lines and beauty of this Classic Rifle. This sight sits .062" lower than our standard 336 / 1895 sight allowing the use of a lower front sight than our standard receiver sight.
Elegant and functional this sight fits all 336 / 1895 style receivers.
BLUE $90 BRASS $95 STAINLESS $100
(While this sight looks amazing on ALL large frame Marlins, it is exceptionally attractive on the Octagon Barreled Cowboy)
Windage adjustment is accomplished by sliding the dovetail piece left or right in its slot. The fit is tight, so you may need a BRASS PUNCH to move it. Once adjusted, it is locked in place with the set screw on top of the sight in front of the peep. When adjusting,move the rear sight in the direction you want to bullet impact to move.
Elevation adjustment is accomplished by turning the peep on its threaded shaft to raise or lower the aperture. One half turn will move the point of impact about 2 inches at 100 yards, depending on your sight radius. The aperture can be threaded into the peep stem from either side. Once adjusted, the peep stem is locked in place using the set screw on the side of the dovetail piece.
To install the 1895 or 336 RELIABLE sight it is necessary to remove the dovetail piece to tighten the mounting screw under the dovetail. Caution is required to avoid injury when the dovetail piece is removed. The corners of the dovetail slot are sharp. Use a BRASS PUNCH wooden dowel, or plastic punch to remove the dovetail.
This sight measures .480" from the top of the receiver to the center of the aperture.